About Landscape Lighting Nashville

Landscape Lighting Nashville for Beginners

Mount the transformer on the wall surface near your GFCI electrical outlet, installing it a minimum of one foot over ground degree. When installing to brick surfaces, be certain to make use of a masonry bit as well as plastic/lead supports to make certain a safe and secure installation. If you choose, stake the transformer into the ground near your picked GFCI electrical outlet instead, mounting it a minimum of one foot aboveground.




Run the wires from the light assembly via the riser base. Connect the lights to the wire, which have clamps with metal teeth with the ability of puncturing circuitry covers to touch the electric line. After tapping the lights right into the wiring, strip completions of the reduced voltage power cord, and link them to the terminals on the transformer.


Make final modifications later at night and hide your cables the list below day. This helps make certain that whatever is good to go for screening and stops you from having to perform way too much manual labor in the dark. Program your lights, setting the timer for the hrs you want the lights on/off.


This blog site is made available by Mr. Electric for instructional objectives only to give the reader basic info as well as a basic understanding on the specific topic over (Landscape Lighting Nashville). The blog should not be used as a substitute for a certified electrical expert in your state or region.

Landscape Lighting Nashville Fundamentals Explained

The transformer senses darkness and turns on the lights at sunset. I choose this instead of a timer, specifically because it will certainly not require to be reprogrammed as the days differ in size throughout the year.


Well, of course once I got ready to mount our lights, I realized I needed much more. I was able to buy comparable lights from an e, Bay seller.


The following tutorial is based upon the Profile transformer I acquired. Your instructions might differ. You will need to find your transformer near an outdoor GFCI electrical outlet. Fortunately I had my electrician mount an outlet last year. (Yes, there are some points that I will certainly leave to an expert. Including brand-new wiring is among them.) Procedure up 18 from the ground (or the elevation recommended in your directions) as well as make use of the template that included your transformer to pierce two pilot openings for the mounting screws.


Screw the installing screws in, leave them expanded partly to approve the holes on the Clicking Here back of the transformer. Split the end of your low voltage cable. Then strip a small quantity off completions utilizing your wire cutters. Slide the cables with the holes on the transformer and also tighten up the screws over the wire.

A Biased View of Landscape Lighting Nashville

Nevertheless, if you unintentionally reduce your cable, you will need to re-install your lights around again! NOT COOL! Run the cable into the trench until you reach your very first light. The directions that included the transformer describe that you desire your first light to be at or additionally than 10 from the transformer.


Make sure your light isn't so close to the transformer that it would be reviewed by the image sensing unit (the very same holds real for having your transformer as well close to your house lights.) Make a loop around your light. This secures the wire from being as well tight and also will ideally protect against all your lights from being uprooted must someone mistakenly (or deliberately) play soccer with one them.


Put the cable into the connector. After that push the connector back with each other firmly. Unless you have very human hand toughness, you may want to utilize pliers (I utilized my Irwin Groove Lock Pliers) to press them together. You require to insure that the steel prongs puncture via the cable insulation and also make contact with the cord inside.


Put the risk of your light right into the ground. Repeat for the staying try here lights. When you reach the end, you might want to "cap" off the end of the cable with duct tape.

The Greatest Guide To Landscape Lighting Nashville

Needless to claim, she had to dig up every informative post single light and also press all the connections tight again. The next day she spent too much time on hold with the consumer service numbers for the transformer and the light supplier.


"Yes, I read the directions. Yes, I checked the connections. Yes, yes. OF COURSE! Okay many thanks (or no many thanks!)" But, she knew she was smarter than the typical bear, so she methodically got rid of one light at a time and afterwards turned on the transformer. Upon removing the last light and also connecting in the transformer she found that they unexpectedly functioned.


Forever measure as soon as all the lights are functioning, cover the connectors in Scotch Strong All-Weather duct tape to maintain them secured and also linked. Call it overkill, yet I really did not intend to end up like Whitney. It does not need to be pretty to be function. Just ask Pretty Good-looking Guy, given that this does remind me a LOT of that blog post he created for me.


This is a relatively very easy install. Landscape lights can improve your visual appeal, and additionally the value of your residence.